Kingroon KP3S 3.0 Firmware Download

Kingroon KP3S Stock Firmware

There are three kinds of MCU of Kingroon KP3S 3D printer mainboard, STM32 F407, GD32 F303, STM32 F103. Before you flash your firmware please double confirm your MCU verison. Wrong version flashed would brick your mainboard. 

Kingroon KP3S 3.0 with MCU GD32 F303

Kingroon KP3S 3.0 with MCU GD32 F303 firmware to DOWNLOAD. (Updated on 2022.3.12)

Get Kingroon KP3S 3.0 mainboard MCU GD32 F303 with stock firmware flashed HERE.

Get Kingroon KP3S 3.0 mainboard MCU GD32 F303 with Marlin firmware flashed HERE.

Kingroon KP3S 3.0 with MCU GD32 F303

Kingroon KP3S 3.0 with STM32 F103

Kingroon KP3S 3.0 with MCU STM32 F103 firmware to DOWNLOAD(Updated on 2022.3.12)

Get Kingroon KP3S 3.0 mainboard MCU STM32 F103 with stock firmware flashed HERE.

Get Kingroon KP3S 3.0 mainboard MCU STM32 F103 with Marlin firmware flashed HERE.

Kingroon KP3S 3.0 with MCU STM32 F103

Kingroon KP3S 3.0 with STM32 F407

Kingroon KP3S 3.0 with MCU STM32 F407 firmware to DOWNLOAD.

Kingroon KP3S 3.0 with MCU STM32 F407

 

Kingroon KP3S 3.0 BLTouch Firmware 

Kingroon KP3S 3.0 with BLTouch leveling sensor modification firmware to DOWNLOAD. BLTouch installion on Kingroon KP3S 3D printer tutorial available on our blog as well.

Kingroon KP3S 3.0 Laser Head Firmware

Kingroon KP3S 3.0 with laser head modification firmware to DOWNLOAD. Tutorial of adding laser head for our Kingroon KP3S

 

Previous article ChituBox Slicer V1.8.1 for Kingroon KP6 Download

Comments

minedgeekble - January 3, 2022

I just sent the video to the email you asked me to send. Please check it out.
I sent an e-mail to dldhswn0526@gmail.com to the address you requested.

Christoph - December 30, 2021

@Lars there is a robin-nanao_cfg file on jour defice or post us the M501 outpput, my values are totaly fxxxxed since using this firmware

Christoph - December 30, 2021

What is the correct Firmware for a KP3S110218XXX

Lars - December 30, 2021

Good day,
i am a proud owner of a Kingroon KP3S. I wanted to calibrate my extruder because it doesn’t extrude by 10mm. Unfortunately I don’t know exactly which firmware is on it to set this with Ponterface (the E-Steps). I also lack the M commands to get the necessary information. Hope you can help me further. Translated with Google Translate.

Thank you very much.

Christoph - December 29, 2021

Hi,

with the Flash of my F103 all drivers are now in reverse …

NoTaMu - December 28, 2021

Isn’t this method accurate?
https://i.postimg.cc/FHgjPSgC/KP3-S-Firmware-Version.png

KINGROON Office - December 28, 2021

@minedgeekble
Is the position of the extruder not heating up or the fan is not turning? What does the display indicate?

KINGROON Office - December 28, 2021

minedgeekbleminedgeekble Can you take a video to see it? My email is supportkingroon.com

minedgeekble - December 26, 2021

I think the board broke during firmware update, but is it not repairable in Korea?

Kingroon Official - December 23, 2021

@minedgeekble
Hi minedgeekble, you could get our mainboard on our official eshop:
https://kingroon.com/collections/kingroon-3d-printer-mainboard

Leave a comment

* Required fields